Menu
Slice Engineering Mosquito Magnum Hotend Bare Bones

Slice Engineering Mosquito Magnum Hotend Bare Bones

Introducing the Mosquito Magnum Hotend Bare Bones. The latest enhancements to the product include an updated heat break that boasts a reinforced throat and a revised radiator design, meticulously crafted to prevent damage during installation and repairs. Additionally, a new heat sink that features a wider opening for the filament path. This improvement significantly enhances compatibility with multi-material setups, such as the Prusa MMU or Mosaic Palette, ensuring a smoother, more reliable multi-material printing experience.Recommendation Use on high flow applications.Bare bones set now including just the followingMosquito HotendM1.3 hex key(x2) M2.5 mounting screws Čtěte více

Na objednávku

4289 Kč

Popis

Introducing the Mosquito Magnum Hotend Bare Bones. The latest enhancements to the product include an updated heat break that boasts a reinforced throat and a revised radiator design, meticulously crafted to prevent damage during installation and repairs. Additionally, a new heat sink that features a wider opening for the filament path. This improvement significantly enhances compatibility with multi-material setups, such as the Prusa MMU or Mosaic Palette, ensuring a smoother, more reliable multi-material printing experience.

Main Benefits

  • The Mosquito Magnum prints up to 20% faster than any other hotend on the market
  • A thermal insulator protects the extended melt zone from the effects of active cooling, and radiative heat loss. It has a heat transmission rate as low as 3 W/m*K, meaning you can have ultimate confidence in the speed of your print, while at the same time maintaining the high resolution benefits achieved with the standard Mosquito
  • The melt zone is extended proximally upwards to maintain a small form factor
  • A multi extrusion setup with both high flow and high resolution optimized designs can be created without needing to purchase new nozzles or make carriage modifications to accommodate hotends of different sizes

The hot block included in this product is compatible with the RepRap standard of nozzles.

About the revised version

Slice Engineering released a brand new version of the Mosquito Magnum! This new versions include a revised heat break and heat sink with cool new features. The new heat break has a reinforced throat and revised radiator to prevent damage during installation or repairs. It also features the same WS2 anti-stick coating found on our line of Vanadium™ Nozzles for even better performance with PLA. The new heat sink has a wider opening for the filament path to more readily accept spliced filament from multi-material setups, like the Prusa MMU or Mosaic Palette.

The old-style heat breaks and heat sinks will not be compatible with the new ones. However, customers that desire to upgrade can retrofit their Mosquito to take advantage of the new features by acquiring both the heat sink and heat break together.

The Mosquito Versatility

The Mosquito is adaptable to virtually any printer, so by swapping one component, you gain the high performance benefits of a printer worth thousands more. Since the Mosquito (designed for beauty) and Mosquito Magnum (designed for speed) are the same length, any combination of these hotends can be mounted to one carriage. So you can switch between high-flow and high-precision in the same print.

Additional Details

  • Superior heat break performance
  • The heat break conducts 85% less heat into the heat sink than a typical threaded heat break
  • Steep temperature gradient at the heat break, and high tolerances along the filament path allow for better transmission of fine motor movements, resulting in beautiful, higher resolution prints
  • Steep temperature gradient at the heat break reduces the likelihood of jamming
  • Reduced heat transmission removes the need for a large heat sink
  • Composite construction of the heat break allows for the use of materials optimized for heat transfer in each section of the heat break
  • Allows for hotend to be mounted with a printed, plastic adapter, without raising safety concerns
  • Increased structural rigidity
  • The heat break has been separated from the structural components of the hotend, allowing for a heat break that is not load bearing, and can be very thin walled. This allows for a reliable, rigid exterior structure
  • No components are prone to loosening at the mounting points
  • Nozzles can be changed with one hand, without grasping the hot block
  • In the case of a severe crash, an entirely new hotend is not necessary, parts can be easily swapped out
  • Larger temperature operating range
  • Specially-engineered high temperature copper alloy in the hot block will not soften at high temperatures in excess of 550C.
  • Threads in the hot block will not deform at high temps, allowing removal of nozzles even after multiple high temp heat cycles
  • Nickel plating on the hot block reduces radiative heat loss and prevents galling of threads
  • Modular/adaptable to almost any FFF/FDM printer
  • Compact, flat, ambidextrous form factor
  • 5 different hole mounting patterns to allow for adaptation to virtually any printer
  • Printable adapters can be created to diversify mounting options
  • Ideal for multiple extrusion systems
  • Small form factor and light mass allows for back-to-back mounting with small nozzle-nozzle distance
  • Lightweight
  • Small mass allows for more rapid motion
  • Less reinforcement needed for the motors, belts, and drives in the motion system



Slice Engineering Mosquito Magnum Hotend Bare Bones

Slice Engineering Mosquito Magnum Hotend Bare Bones
Slice Engineering Mosquito Magnum Hotend Bare Bones

4289 Kč

Nový dotaz k produktu

Kontrolný kód

i

Potřebujete poradit s výběrem zboží? 

Jsme tu pro Vás!

+420 572 155 055   

(Po - Čt 8:00 - 15:00, Pá 8:00 - 14:00)

info@na3D.cz

 

Dostupnost Bambu Lab

Tiskárny skladem, více info zde

Přihlášení

Zapomenuté heslo

Předvolby soukromí
Soubory cookie používáme k vylepšení vaší návštěvy tohoto webu, k analýze jeho výkonu a ke shromažďování údajů o jeho používání. Můžeme k tomu použít nástroje a služby třetích stran a shromážděná data mohou být přenášena partnerům v EU, USA nebo jiných zemích. Kliknutím na „Přijmout všechny soubory cookie“ vyjadřujete svůj souhlas s tímto zpracováním. Níže můžete najít podrobné informace nebo upravit své preference.

Zásady ochrany soukromí

Detailní nastavení
Tento web je chráněn reCAPTCHA a Google. Platí Zásady ochrany osobních údajů a Smluvní podmínky.

Přihlášení

Zapomenuté heslo

Produkt byl vložen do košíku
Pokračovat v nákupu Objednat